The simplest way to test if your place is suitable for a mobile booster is to check the signal bars on your phone on the outside of your property.
Be aware for 1-2 bars is highly recommended that you upgrade to a more powerful antenna than that provided in the standard kit. You can do this by choosing the upgrade option (Yagi) in the product page.
We sell high-quality products which are all capable of simultaneously supporting multiple devices. The limit for each booster mainly depends on its output power or ‘dBs’. We have provided a list of devices and their support limit converted to dBs below:
Estimations can also be made using this table:
|Coverage in square metres||Number of supported users|
|Up to 1600 sq. ft.||Up to 50 users|
|Up to 3300 sq. ft.||Up to 100 users|
|Up to 6500 sq. ft.||Up to 150 users|
|Up to 16.000 sq. ft||Up to 200 users|
Signal boosters also known as Bi-directional amplifiers (BDA's), repeaters or amplifiers work by capturing a signal outside the home, building, automobile, boat, warehouse, etc…,with an exterior antenna, bring it inside, amplify it, and rebroadcast it. For most of the products on this site, there are four main components: the Outside Antenna, the Amplifier (booster), the Inside Antenna, and the cabling to connect everything.
The Outside Antenna
The outside antenna can be omni-directional (can capture signal from all directions) or directional (works best when pointed in the direction of a cell tower).
The benefit to omni-directional antennas is that they are easy to install and pick up signals in a 360 degree horizontal plane, making them suitable to picking up signals from cell towers in different directions. You want to mount them as high as possible where the signal is strongest. A few disadvantages of omni-directional antennas:
1) Their gain is typically much lower than a directional antenna.
2) They are more prone to other RF interference.
3) They are more prone to pick up the signal from the indoor antenna, resulting in system oscillation (see more on this below).
4) Most omni-directional antennas are not wide band meaning that they will not work well for any frequencies outside of the 850 MHz or 1900 MHz bands.
The benefit to directional antennas (Yagi antennas) is that they typically provide more signal gain (power) than omni-directional antennas. They are also less prone to other RF interference. A disadvantage to the yagi antenna is that it will take more time to install because it must be pointed at your carrier's cell tower. Also, if looking to boost the signal for multiple carriers and the towers are not in the same general direction this may not be the antenna for you or you will need to combine multiple yagi antennas on the roof. The ST-Yagi antenna is a good example of a popular wide band (698-2700 MHz) directional outdoor antenna which provides 8-10dB of gain and will work with all carriers and cell phone technologies in existence today. Yagi's can also be band specific. Band specific yagi antennas provide even more gain than a wide band yagi but must be pointed exactly at your carrier's tower as the beam width (pickup pattern) is much narrower than a wide band yagi.
Reasons to choose a Yagi (directional) Antenna:
We Recommend the Wide Band Yagi to the vast majority of our customers.
Reasons to choose an omni-directional antenna:
Every amplifier (or booster) must provide at least two ports, an input and an output. While higher end models will have more sophisticated circuitry, higher gains, and adjustable uplink and downlink gains, they all function pretty much the same. The signal coming in from the outside antenna is amplified and sent to the inside antenna. Every signal amplifier has a specification called Gain. Without getting too technical, gain is defined as the ratio of output to input. When specifying RF power, gain is measured in dB (decibels). dB numbers are derived from a fairly simple logarithmic function, however all you need to know is that every increase in 3 dB doubles the power. Ex. 1 watt into a 3 dB amplifier would come out as 2 watts. 1 watt into a 6 dB amplifier would come out as 4 watts. For more, please reference the following:
When searching for an amplifier for your particular application, please reference the following table:
|dB Gain||Applicable To||Antenna Separation|
|<20 dB||Automobile, Boat||4 ft. or direct connect.|
|30 dB||Automobile, Boat||5 ft. or direct connect.|
|40 - 45 dB||Large Auto, RV, Large Boat||6 ft. – 20 ft.|
|50 dB||1-2 Rooms in a Home||30 ft. – 50 ft.|
|55 dB||Small home up to 1,500 sq. ft.||50+ ft.|
|62 dB||Up to 5,000 sq. ft. Home, Office, Warehouse||60+ ft.|
|68 dB||Up to 7,000 sq. ft. Home, Office, Warehouse||75+ ft.|
|70 - 80 dB||Large Home / Commercial Application||100 + ft.|
Please keep in mind that this table represents general rules of thumb and the recommended applications and antenna separation distances may vary by product/manufacturer, outdoor signal strength, cable lengths and antennas. Antenna separation distances are to keep your amplifier from going to oscillation. In the audio world, this is analogous to getting a microphone too close to a speaker, thus producing feedback. If you choose directional indoor (wall mount panel) and outdoor (yagi) antennas or there is metal or multiple walls separating the antennas, often times these distances can be much shorter than the distances listed above. Also, increasing the vertical component of the separation as much as possible will reduce the required separation as well. These are straight line distances with both horizontal and vertical components, not distances based on the cable lengths.
The Inside Antenna
Inside antennas, just like outside antennas, come in different shapes and sizes and serve different purposes. Most of the other in-building amplifier products on this site have a separately mounted internal antenna. The most popular antenna for providing omni-directional internal coverage is the ceiling-mounted dome antenna. This type of antenna is a little more difficult to install than one that is directly attached to the amplifier, but is less obtrusive and typically provides more gain than a directly connected antenna. A dome antenna provides 360 degrees of horizontal coverage in a downward direction, making them ideal for covering a single floor with a more or less square layout. Inside antennas can be directional as well. If you are you looking to provide directional coverage for a large, open space or hallway, the wall-mounted panel antenna provides this. A panel antenna can also be installed in an attic (facing downward) for single floor coverage with tall ceilings. They may also be installed facing downward on lower ceilings for mutiple floor zoned coverage.
General Purchasing Recommendation
Reasons to choose a ceiling mounted dome antenna:
Reasons to choose a wall mounted panel antenna:
The cabling and connectors used to connect the outside antenna to the amplifier as well as the inside antenna to the amplifier play a crucial role in how your system will perform. Depending on the product, different types of cabling and connectors can be used. Your amplifier has to receive the highest quality signal possible in order to provide full indoor coverage. For this reason, it is recommended that runs using RG6 should be no more than 60 ft. For runs longer than 60', RG11 should be used. For most of the other products on this site LMR-400 50 Ohm Coax is the standard. In comparison, while LMR-400 is more expensive and thicker, it only loses about 3-6 dB per 100 ft for cellular and PCS frequencies respectively. Based on this, LMR-400 can be run further than RG6 before there is a decrease in system performance. For all three-piece systems (outside antenna, amplifier, inside antenna) it is recommended the amplifier be installed as close to the external antenna as possible. Ex. If the external antenna is installed on a roof, it is recommended the amplifier be installed in the attic as opposed to the basement. The shorter the cable length between the external antenna and the amplifier, the better. Remember that there is no separation limit between the antennas and the amplifier, only between the antennas.
General Purchasing Recommendation
The simplest way to test if your place is suitable for mobile booster installation is to check the signal bars in your phone.
The best signal is 5 bars however perfect coverage is possible in urban places. In suburban rural areas 4 bars is also not bad.
1st step to find out if mobile signal booster will work in your property or not is to check how many bars you do have.
If you have even 1 bar it means booster will help to increase to 5 bars using powerful external antennas
If you have 3 bars booster you won't need so powerful antennas and standard kit will be enough to gain 5 bars.